Tighten the upper clamp knob to secure the top of the glass tube.
Inspect the filament loop for physical breaks. Check and replace the rear-panel fuses if necessary.
The dual-stage vertical micropipette puller remains a cornerstone instrument in electrophysiology and microinjection laboratories worldwide. Utilizing gravity-fed vertical pulling mechanisms paired with highly uniform heating elements, it consistently fabricates glass micropipettes with tip apertures ranging from a few tens of microns down to sub-micron thresholds (
If the coil accumulates debris, run a high-heat cycle without any glass installed for 2–3 seconds to burn off residues. Troubleshooting Common Issues Probable Cause Corrective Action Glass does not break / melts completely Heater value is set too low or too high. Readjust dials incrementally by 2–3 units. Asymmetrical pipette tips Heating coil is uncentered or distorted. Let the unit cool, then manually center the coil. Inconsistent pipette resistance Drafts in the room or friction on the shaft. Close the draft shield; clean the vertical shaft. Unit will not turn on Blown fuse or faulty power connection. Check the rear fuse drawer and replace if necessary. 6. Conclusion
Initiates the heating and pulling cycle or resets the sliders. 4. Step-by-Step Operating Instructions
The PC-10 doesn’t need a software update. It needs a guide that speaks to the modern tinkerer. The rise of "narishige pc10 manual new" as a search term isn’t about buying a fresh machine—it’s about with fresh documentation.
Check that the glass is centered in the heater coil and that the platinum filament is not damaged. 6. Maintenance of the PC-10
What is your specific (e.g., patch-clamp, microinjection, IVF)? Share public link
Narishige's global support page also offers the ability to request PDF newsletters and contact their technical teams directly, which can be helpful for specific queries.
Place the finished pipettes immediately into a dust-free storage jar or a covered pipette holding tray. 4. Parameter Optimization and Troubleshooting
Tighten the upper clamp knob to secure the top of the glass tube.
Inspect the filament loop for physical breaks. Check and replace the rear-panel fuses if necessary.
The dual-stage vertical micropipette puller remains a cornerstone instrument in electrophysiology and microinjection laboratories worldwide. Utilizing gravity-fed vertical pulling mechanisms paired with highly uniform heating elements, it consistently fabricates glass micropipettes with tip apertures ranging from a few tens of microns down to sub-micron thresholds ( narishige pc10 manual new
If the coil accumulates debris, run a high-heat cycle without any glass installed for 2–3 seconds to burn off residues. Troubleshooting Common Issues Probable Cause Corrective Action Glass does not break / melts completely Heater value is set too low or too high. Readjust dials incrementally by 2–3 units. Asymmetrical pipette tips Heating coil is uncentered or distorted. Let the unit cool, then manually center the coil. Inconsistent pipette resistance Drafts in the room or friction on the shaft. Close the draft shield; clean the vertical shaft. Unit will not turn on Blown fuse or faulty power connection. Check the rear fuse drawer and replace if necessary. 6. Conclusion
Initiates the heating and pulling cycle or resets the sliders. 4. Step-by-Step Operating Instructions Tighten the upper clamp knob to secure the
The PC-10 doesn’t need a software update. It needs a guide that speaks to the modern tinkerer. The rise of "narishige pc10 manual new" as a search term isn’t about buying a fresh machine—it’s about with fresh documentation.
Check that the glass is centered in the heater coil and that the platinum filament is not damaged. 6. Maintenance of the PC-10 Readjust dials incrementally by 2–3 units
What is your specific (e.g., patch-clamp, microinjection, IVF)? Share public link
Narishige's global support page also offers the ability to request PDF newsletters and contact their technical teams directly, which can be helpful for specific queries.
Place the finished pipettes immediately into a dust-free storage jar or a covered pipette holding tray. 4. Parameter Optimization and Troubleshooting