Brushless Esc V2.3 Manual ((install)) Jun 2026
Plug the black/red/white signal cable into the Throttle (CH2) slot on your radio receiver. Black: Ground (-) Red: Power (+) White: Signal (S)
Switch on the transmitter and move the throttle stick to the (top) position.
Re-solder any loose wires. Check for broken internal motor windings. Throttle channel reversed on transmitter
Some V2.3 units have a physical jumper labeled "BRK" (Brake) on the corner. Shorting two pins enables Mode 1.
A: Either reverse the throttle channel on your transmitter (Servo Reverse) or swap any two motor wires. brushless esc v2.3 manual
"Soft Cut" (reduces power gradually) or "Hard Cut" (shuts off motor immediately).
Leave the throttle trigger in neutral and press the "SET" button once. (1 flash).
Wait another 5 seconds: The motor will emit a musical tone, confirming entry into programming mode. Step 2: Selecting Parameters
| Specification / Programmable Item | Typical Options / Values | | :--- | :--- | | | 45A, 60A, 80A (varies by model) | | Burst Current | 180A, 320A, 480A (varies by model) | | Input Voltage | 6-12V, compatible with 2-3S LiPo | | Running Mode | Forward with Brake / Forward & Back with Brake / Direct Forward & Back | | Drag Brake | 0% · 5% · 10% · 20% · 40% · 60% · 80% · 100% | | Low Voltage Cut-off | No Protection · 2.6V · 2.8V · 3.0V · 3.2V · 3.4V (per cell) | | Start Mode / Punch | Class 1 (Very Soft) to Class 9 (Very Aggressive). Default: Class 7 | | Brake Force | 25% · 50% · 75% · 100% | | Reverse Force | 25% · 50% · 75% · 100% | | Neutral Range | 6% (Narrow) · 9% (Normal) · 12% (Wide) | | Motor Timing | 0.00° · 3.75° · 7.50° · 11.25° · 15.00° · 18.75° · 22.50° · 26.25° | | Over-heat Protection | Protect · Non-protect | Plug the black/red/white signal cable into the Throttle
: Leave the throttle trigger in the neutral position and short-press the button. The ESC will beep once. Full Throttle
The V2.3 architecture introduces upgraded MOSFETs and an enhanced microcontroller unit (MCU) capable of handling higher PWM frequencies. This results in smoother throttle responses and lower operating temperatures. Specification 60A (with proper airflow) Peak Current (10 sec) Input Voltage Range 2S–6S LiPo (7.4V – 22.2V) BEC Output Switch-mode: 6.0V / 7.4V adjustable (5A) MCU Architecture 32-bit ARM Cortex Supported Protocols PWM, OneShot, DShot300/600, ProShot Weight / Dimensions 42g / 55mm x 28mm x 12mm Protection Systems Thermal, Low-Voltage Cutoff, Signal Loss Wiring and Connection Diagrams
Battery voltage is outside the acceptable operational range (too high or too low). Check battery state of charge. Flash / Beep Sequence After Throttle Input:
Pull the transmitter throttle to full forward/acceleration and press the "SET" button. (2 flashes). Check for broken internal motor windings
Correct wiring ensures electrical efficiency and prevents short circuits. Follow the diagram logic below. 1. Connection Steps
Brushless ESC V2.3 Manual: Complete Setup, Wiring, and Programming Guide
The V2.3 ESC is designed for enthusiasts who demand waterproof durability and precise control. It is compatible with sensorless brushless motors and offers a high-performance 32-bit MCU (in some iterations) or a reliable analog system, often featuring a 5V/3A or 12V/2A BEC. Key Features
The motor coasts to a stop when throttle is cut. Ideal for airplanes.